The SAT-TECH SF-9505A is compatible with DISH (Network), FTA, and Directv (not SWM) satellite TV service types. With a digital readout, it makes for easier pointing. Perfect for repointing your home dish or using for mobile satellite TV viewing. Frequency range:950-2150MHz.
Very powerful Digital Satellite Signal Meter Finder which is able to find satellites in a very quick way about within 15 minutes if no accident. It is very lightweighted and compact,very convenient to use.Anti-corrosion connectors also make sure long time use and it is very worthy of trying.
Input Frequency: 950-2150 MHz
Input Level Min: -40dBm
Input Level Max: -10dBm
Input Impedance: 75Ω, F connector
Output Impedance: 75Ω, F connector
Power Supply: DC 13/18 V
Operating Range (LNB gain): 52-60dB
1* Digital Satellite Signal Meter Finder
1* Compass for free
3.5 Inch High Definition TFT LCD Screen
Fully DVB-S/S2, MPEG-2/MPEG4 compliant
MPEG-2 / H.264 Hardware decoding
Digital meter for signal strength and quality
Supports for multiple TP detection
Supports scan of Auto,Blind,Manual or NIT
Sound and Light Alarm for Locking Signal
Auto Calculate Angle of AZ ,EL
Supports DISEQC 1.0/1.1/1.2 ,0/22khz Tone Speaker Integrated
Support both AV out and AV in
Supports HDMI out
LNB short protect
7.4V/3000mAh Li-ion Battery Included
Easy to carry.
Software can be upgraded to search the updated satellites via USB port. The software is used to search the US satellites, but it can search EU satellites via software update. However, two softwares can't exist in the same time. Pls email us before you upgrade the Software, we will provide you with detailed instructions.
Simplified MENU OSD Instruction:
After power on, press ok into the main menu and start to set below functions:
For OSD Language/Channel Name/BandWidth/ Carrier/ Modulate/FEC/Guard Interval/Output Level/Signal Source functions setting: You can press◀▶;to change or select them.
For Frequency setting: You can press◀▶ move cursor and press ▲▼ key to change numbers.
For Key Tone setting: press◀▶o ON/OFF.
For Service Provider/ Program Name setting: just input the name is ok.
For Factory Setting: press OK to confirm.
After setting above, you can use it normally. For detailed instructions, pls refer to the user menu. If you still can't search the satellites, pls contact us by email
- Transmission Standard: DVB-S/S2
- Antenna connection: F-Type
- Frequency range: 950-2150 MHz
- Signal level: -65 dBm~-25 dBm
- LNB Switch: 22KHz
- LNB Voltage: 13/18 V, max 300 mA
- Demodulation: QPSK
- Symbol Rate: 2
- LCD Type: FSTN positive transflective
- Number of Dots: 128x64
- Active Area (WxH): 59.6x43 mm
- Connector: USB
- Data Protocol: USB to RS232
- Li-ion Battery: 8.4V 800 mAh
- Power Supply: Output DC12V/1A; Input 100-240V AC 50/60Hz
- Power Consumption: Max.5W
- Dimension: 8cm x16cm x4cm
- Net weight: about 250 g
- 1 x WS-6933 DVB-S2 DVB-S HD Satellite Finder
- 1 x Power Supply
- 1 x USB Cable
- 1 x Silicone Case
- In Retail Package
Frequency range : 950-2150MHz
Supply voltage : 13-18V DC
Input level range : -40dBm~ -10dBm
Operating temperature : 0-40
Impedance : 75Ω
Use LCD to display the satellite signal intensity
Built-in signal alert buzzer
With LCD backlight / buzzer and attenuation control function
DC pass to LNB
ATT increasing key. If the incoming signal is too strong, (the thermometer-scales shows max and the signal strength value shows 99) it can easily be attenuated by enabling this "attenuation" funtion, it reduces the incoming signal to a lower level. There are four step attenuation totally.
How to connect
connect a jumper cable from the LNB to the "Satellite" port on the digital SATFINDER.
connect the cable from your satellite receiver to the "Receiver" port on the digital SATFINDER.
To avoid a continuous full scale reading, do not use the digital SATFINDER directly in front of the dish.
When using a LNB with gain higher than 60dB, insert a 5dB attenuator between the LNB/LNBF and the digital SATFINDER.
In case no satellite receiver is at hand a 13-18V DC power supply with F-connector can be connected on the "Receiver" side of the digital SATFINDER to power the SATFINDER.
The follow link will show you how to use it,Just click it
1 x SF-95DR Digital satellite finder
1 x User manual
How to use a digital satellite finder.
These are the 5 elements of cloud robotics
Robots haven’t yet lived up to their potential, but they’re about to benefit enormously from the Cloud. I’ll describe how a new generation of robots can use wireless networking, big data, machine learning, open-source, and the Internet of Things to improve how they assist us in tasks from driving to housekeeping to surgery.
Ford versus Holden , the definitive Australian automotive rivalry, seen here but not as we know it. There’s not a V8 engine, a sedan body or a rear-wheel-drive configuration in sight.
Instead, we have a pair of hot hatches, both (re)launched inside the past few months, that go about doing broadly the same thing as each other in notably...Source: CarAdvice
The data is used in digital map making ... subset of this data has been released at a grid resolution of 30 meters, about 1 / 3 the length of a football field. In April 2011, the satellite switched itself into power-saving mode due to deterioration ...
A forecast satellite visibility based on a 3D urban model to exclude ... building on the map could be obtained from the 2D GIS data. In this article, the 3D digital surface model (DSM) data is provided by Aero Asahi Corporation. Figure 2 shows the process ...
has reaffirmed the validity of two of the company's key Smart Electric Meter Patents covering digital electric meters equipped with an internal wireless communications module and antenna. TransData received notice that the Patent Office will issue ...