The SAT-TECH SF-9505A is compatible with DISH (Network), FTA, and Directv (not SWM) satellite TV service types. With a digital readout, it makes for easier pointing. Perfect for repointing your home dish or using for mobile satellite TV viewing. Frequency range:950-2150MHz.
Frequency range : 950-2150MHz
Supply voltage : 13-18V DC
Input level range : -40dBm~ -10dBm
Operating temperature : 0-40
Impedance : 75Ω
Use LCD to display the satellite signal intensity
Built-in signal alert buzzer
With LCD backlight / buzzer and attenuation control function
DC pass to LNB
ATT increasing key. If the incoming signal is too strong, (the thermometer-scales shows max and the signal strength value shows 99) it can easily be attenuated by enabling this "attenuation" funtion, it reduces the incoming signal to a lower level. There are four step attenuation totally.
How to connect
connect a jumper cable from the LNB to the "Satellite" port on the digital SATFINDER.
connect the cable from your satellite receiver to the "Receiver" port on the digital SATFINDER.
To avoid a continuous full scale reading, do not use the digital SATFINDER directly in front of the dish.
When using a LNB with gain higher than 60dB, insert a 5dB attenuator between the LNB/LNBF and the digital SATFINDER.
In case no satellite receiver is at hand a 13-18V DC power supply with F-connector can be connected on the "Receiver" side of the digital SATFINDER to power the SATFINDER.
The follow link will show you how to use it,Just click it
1 x SF-95DR Digital satellite finder
1 x User manual
- Transmission Standard: DVB-S/S2
- Antenna connection: F-Type
- Frequency range: 950-2150 MHz
- Signal level: -65 dBm~-25 dBm
- LNB Switch: 22KHz
- LNB Voltage: 13/18 V, max 300 mA
- Demodulation: QPSK
- Symbol Rate: 2
- LCD Type: FSTN positive transflective
- Number of Dots: 128x64
- Active Area (WxH): 59.6x43 mm
- Connector: USB
- Data Protocol: USB to RS232
- Li-ion Battery: 8.4V 800 mAh
- Power Supply: Output DC12V/1A; Input 100-240V AC 50/60Hz
- Power Consumption: Max.5W
- Dimension: 8cm x16cm x4cm
- Net weight: about 250 g
- 1 x WS-6933 DVB-S2 DVB-S HD Satellite Finder
- 1 x Power Supply
- 1 x USB Cable
- 1 x Silicone Case
- In Retail Package
3.5 Inch High Definition TFT LCD Screen
Fully DVB-S/S2, MPEG-2/MPEG4 compliant
MPEG-2 / H.264 Hardware decoding
Digital meter for signal strength and quality
Supports for multiple TP detection
Supports scan of Auto,Blind,Manual or NIT
Sound and Light Alarm for Locking Signal
Auto Calculate Angle of AZ ,EL
Supports DISEQC 1.0/1.1/1.2 ,0/22khz Tone Speaker Integrated
Support both AV out and AV in
Supports HDMI out
LNB short protect
7.4V/3000mAh Li-ion Battery Included
Easy to carry.
Software can be upgraded to search the updated satellites via USB port. The software is used to search the US satellites, but it can search EU satellites via software update. However, two softwares can't exist in the same time. Pls email us before you upgrade the Software, we will provide you with detailed instructions.
Simplified MENU OSD Instruction:
After power on, press ok into the main menu and start to set below functions:
For OSD Language/Channel Name/BandWidth/ Carrier/ Modulate/FEC/Guard Interval/Output Level/Signal Source functions setting: You can press◀▶;to change or select them.
For Frequency setting: You can press◀▶ move cursor and press ▲▼ key to change numbers.
For Key Tone setting: press◀▶o ON/OFF.
For Service Provider/ Program Name setting: just input the name is ok.
For Factory Setting: press OK to confirm.
After setting above, you can use it normally. For detailed instructions, pls refer to the user menu. If you still can't search the satellites, pls contact us by email
LeaningTech 95DT Satellite Signal Finder Meter is a tool that enables you easily tune your satellite dish while outside. It can help you to find the strongest satellite signal direction and it is suitable for remote satellite antennas. Our LeaningTech 95DT can help you alignment satellite for dishes on homes, RVs and motor homes easily without others help.
a. Connect a jump cable from LNB to the satellite finder's "Satellite" port. Connect the "Receiver" port, a DC 1318V power which comes from the satellite receiver
b. Make sure that the satellite finder is properly connected. Plug in the AC cord and turn on the satellite receiver
c Set the dB to be 1 or 2 by ATT button, the signal LED will show from 15 to 30, then you can adjust the dish postition, when you hear the buzzer alert and the value of signal strength getting more and more, it means you get the statellite signal
d. Set the dB to be 3 or 4, adjust the dish again and again until the value of the signal strength is maximum. Then you can see the LOCK light in the satellite receiver, if the lock light is lighting it shows you find the desired satellite. Otherwise you need to adjust the dish again
-If there is an internal amplifer your antenna, (eg: 01MM-SQ01), it should be powered by an external power supply via a DC power inserter. Make sure the power inserter is positioned between the finder and the antenna.
Satellite finder, how to use a digital sat finder or meter. Easy to find a satellite when you see how the professionals do it. They show you the tricks of the trade and ...
Baumstein, an athlete from Orlando, Florida, waited for weeks to set out in her custom-designed rowboat from Choshi, a port east of Tokyo, headed for San Francisco. With a few last-minute adjustments to her supplies and a brief call to her parents, she rowed out of the marina on Sunday, a tiny sliver on the glittering horizon, hoping to finish the 6,000-mile (9,600-kilometer) journey by...Source: www.startribune.com
(Senior Jenny DeSouchet , a member of the cross country and track and field team, recently sat down with two of her teammates, junior Maddie Alm and freshman Kaitlyn Benner , both Monarch High School alumni, to talk about their success this year. DeSouchet wrote this special feature for CUBuffs.com and will graduate on May 9 with a...Source: www.cubuffs.com